The screencast about NanoWorld AFM probes for Magnetic Force Microscopy held by Dr. Marco Becker has just passed the 1500 views mark. Congratulations Marco!
Magnetic Force Microcopy is a type of Atomic Force Microscopy in which a magnetised AFM tip is used to measure magnetic interactions between the tip and the surface of a magnetic sample. These detected interactions are then used to reconstruct the magnetic structure of the sample surface
NanoWorld currently offers two types of MFM tips:
– MFMR – This type of magnetic AFM tip is coated with a hard magnetic coating on the tip side and yields a very high force sensitivity, while simultaneously enabling tapping and lift mode operation.
– S-MFMR – These magnetic AFM tips are coated with a soft magnetic layer on the tip side and are designed for the measurement of magnetic domains in soft magnetic samples.
The properties of a polymer change significantly depending on the structure of the polymer chain, particularly, with branched structures, depending on the number of branches and the length of the branch.* However, the long-chain branch (LCB) structure of polyethylene was unclear, due particularly to the complex polymer structure and the limitations of its analysis methods.
In their study “Direct Observation of Long-Chain Branches in a Low-Density Polyethylene” Ken-ichi Shinohara, Masahiro Yanagisawa and Yuu Makida measured the chain length of LCBs and the distance between branch points of LDPE by atomic force microscopy.*
Figure 1 from “Direct Observation of Long-Chain Branches in a Low-Density Polyethylene “ by K. Shinohara et al.: Direct measurement of LCB in a tubular LDPE (F200-0 fractionated). (A) AFM image of a single molecule of LDPE on mica in DMTS at 25 °C. X: 279 nm, Y: 209 nm, Z: 18 nm. (B) Length of each chain of LDPE. (C) A wire model of self-shrinking structure of polymer chain of LDPE. Main chain: red wire. LCB: black wire. The model was created to be one tenth of the length of the extended chain based on AFM observation (B), MD simulation (Fig. S1), and the molecular weight determined by SEC-MALLS-Visc experiments (see Fig. 2).
*Ken-ichi Shinohara, Masahiro Yanagisawa, Yuu Makida Direct Observation of Long-Chain Branches in a Low-Density Polyethylene Nature Scientific Reportsvolume 9, Article number: 9791 (2019) doi: https://doi.org/10.1038/s41598-019-46035-9
Open Access: The article «Direct Observation of Long-Chain Branches in a Low-Density Polyethylene» by Ken-ichi Shinohara, Masahiro Yanagisawa and Yuu Makida is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
Polydimethylsiloxane (PDMS) is a promising biomaterial for generating artificial extracellular matrix (ECM) like patterned topographies, yet its hydrophobic nature limits its applicability to cell-based approaches.” Although plasma treatment can enhance the wettability of PDMS, the surface is known to recover its hydrophobicity within a few hours after exposure to air. *
To investigate the capability of a novel PDMS-type (X-PDMS) for in vitro based assessment of physiological cell properties, the authors of the article “Nano- and Micro-Patterned S-, H-, and X-PDMS for Cell-Based Applications: Comparison of Wettability, Roughness, and Cell-Derived Parameters” cited here, designed and fabricated plane as well as nano- and micrometer-scaled pillar-patterned growth substrates using the elastomer types S-, H- and X-PDMS, which were fabricated from commercially available components.*
To assess their applicability to cell-based approaches, Marina Scharin-Mehlmann et al., characterized the generated surfaces using water contact angle (WCA) measurement and atomic force microscopy (AFM) as indicators of wettability and roughness, respectively.*
The surface roughness of the samples was determined by Atomic Force Microscopy in tapping mode. For plane and flat pillar patterned PDMS (130 and 190 nm nominal pillar height) surfaces, a standard tapping mode AFM probe ( Pointprobe® NCHR, NanoWorld) was used. For patterned surfaces with pillars of 1,800 nm height tilt compensated high-aspect-ratio AFM probes (AR5T-NCHR, NanoWorld) were used. The scanning area was 50 × 50 μm2, the scanning rate 0.5 Hz. In this scanning area each roughness value (root mean square roughness Rq) was evaluated from five 10 × 10 μm2 areas.*
Figure 5 from “Nano- and Micro-Patterned S-, H-, and X-PDMS for Cell-Based Applications: Comparison of Wettability, Roughness, and Cell-Derived Parameters” by Marina Scharin-Mehlmann et al.: AFM analysis of structured PDMS substrates. (A) Three-dimensional reconstructions of fabricated pillar-structured PDMS substrates recorded by AFM. (B) Mean pillar height of plane S-, H-, and X-PDMS as measured by AFM. All data are significantly different at a significance level of P ≤ 0.001 as evaluated by two-way ANOVA unless otherwise indicated. Color coding of statistical analysis: within group “130 nm,” purple; within group “190 nm,” pink.
*Marina Scharin-Mehlmann, Aaron Häring, Mathias Rommel, Tobias Dirnecker, Oliver Friedrich, Lothar Frey and Daniel F. Gilbert Nano- and Micro-Patterned S-, H-, and X-PDMS for Cell-Based Applications: Comparison of Wettability, Roughness, and Cell-Derived Parameters Frontiers in Bioengineering and Biotechnology. 2018; 6: 51 DOI: 10.3389/fbioe.2018.00051
Open Access: The article «Nano- and Micro-Patterned S-, H-, and X-PDMS for Cell-Based Applications: Comparison of Wettability, Roughness, and Cell-Derived Parameters» by Marina Scharin-Mehlmann, Aaron Häring, Mathias Rommel, Tobias Dirnecker, Oliver Friedrich, Lothar Frey and Daniel F. Gilbert (2018) is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
